Panels Designed for Long-Term Durability

Metal roofing in Lufkin for buildings with failing fastener systems or rust-compromised panel seams

A worn metal roof shows itself through loose panels that lift during windstorms, rust stains below fastener holes, or water entry along seams where sealant has dried and cracked. R&M Painting and Construction Services installs and repairs metal roofing in Lufkin, working with standing seam and exposed-fastener systems on both residential and commercial properties. Standing seam panels interlock along hidden clips that allow for thermal expansion, while exposed-fastener systems rely on neoprene washers under each screw to maintain a watertight seal—those washers degrade over time and allow water to track down the fastener shaft into the substrate.


Metal roof installation begins with removing old roofing material if a tear-off is required, then installing a high-temperature underlayment that won't degrade from radiant heat conducted through the metal. Panels are fastened to purlins or directly to solid decking, depending on the building's framing, and each panel overlaps the previous one by at least one corrugation to prevent wind-driven rain from entering. Ridge caps, rake trim, and eave flashing are custom-bent to match the panel profile and fastened with the same screw spacing pattern used on the field panels.


Arrange an on-site consultation to review your current panel condition and discuss whether a retrofit over existing shingles or a full tear-off is the better approach.

How Metal Roofing Addresses Long-Term Exposure

Metal roofing performs differently than composition shingles because it doesn't rely on granules or adhesive strips to resist water—the interlocking panel design and continuous fastener seal create a barrier that sheds water through gravity and surface tension. Galvanized or Galvalume coatings protect the steel substrate from oxidation, and factory-applied paint finishes resist UV degradation better than organic shingle mats.


After installation, you'll notice that rain runs off faster because the smooth metal surface has no texture to slow water flow, and panels remain dimensionally stable without the cupping or curling that happens when asphalt shingles age. Fasteners stay tight because the metal doesn't expand and contract as much as wood decking, and properly installed panels remain quiet during rain because the underlayment dampens sound transmission.


Metal roofing systems include closure strips at the eaves and ridge to block insect entry and wind infiltration, and butyl tape sealant along panel overlaps that compresses when fasteners are tightened. Valleys can be formed with separate flashing pieces or by running panels continuously through the valley line, which eliminates a potential leak point but requires precise cuts and careful fastener placement.

Answers About How the Work Is Done

Property owners considering metal roofing often have questions about installation methods, material choices, and maintenance requirements. These answers explain the work itself and what differentiates quality installation.

  • What happens during the roof inspection before installation?

    The existing roof structure is evaluated for adequate framing to support the metal panels, decking is checked for rot or sagging that needs repair, and measurements are taken to determine panel lengths and trim quantities. Any structural issues are identified before materials are ordered.

  • How are standing seam panels different from exposed-fastener panels?

    Standing seam systems use concealed clips that snap into the panel seam and fasten to the roof deck, allowing the panel to move with temperature changes without stressing the fasteners. Exposed-fastener panels are screwed directly through the face of the metal, which creates more potential leak points but costs less and installs faster.

  • Why does the underlayment matter on a metal roof?

    Metal conducts heat, and temperatures on the panel underside can exceed 150 degrees during summer, which deteriorates standard felt underlayment. Synthetic underlayment resists high temperatures and provides a secondary water barrier if a fastener backs out or a panel seam fails.

  • What should you look for once the metal roof is installed in Lufkin?

    Check that all trim pieces are sealed with butyl tape where they meet the panels, fasteners are installed perpendicular to the surface without over-driven screws that crush the neoprene washer, and panel seams are aligned in straight runs without wavy or misaligned edges. Many older homes in Lufkin have gable vents and soffit overhangs that require custom flashing to maintain attic ventilation while keeping weather out.

  • How do you maintain a metal roof after installation?

    Inspect fasteners annually for loose screws or cracked washers, clear debris from valleys and behind roof penetrations, and check that sealant along trim pieces hasn't pulled away from the metal surface. Panels themselves don't require maintenance, but the fastener system and trim connections need periodic attention.

R&M Painting and Construction Services also installs metal roofing in Gilmer and Longview. Metal roof retrofits over existing asphalt shingles require furring strips to create an air gap that prevents condensation and allows the old roof to breathe—schedule a property evaluation to determine whether your framing supports the additional load and whether local building codes permit a retrofit installation.